Samsung Galaxy Young2 Pro G130BUVJU0AQA1
SM-G130BU 1 country Android 4.4.4 (KitKat)

Samsung Galaxy Young2 Pro G130BUVJU0AQA1 Firmware

Samsung Galaxy Young2 Pro G130BUVJU0AQA1 is an Android 4.4.4 (KitKat) firmware for Brazil (ZTM, ZTO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G130BUVJU0APA1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. This is the newest build for SM-G130BU.

9.3/10 (451)17,311 times
Android 4.4.4 (KitKat)
OS Version
2017-01-26
First release
other regions until 2017-06-12
n/a
Security patch
1
Countries
2
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SM-G130BU
    ZTM Brazil
    		G130BUZTM0APK1G130BUVJU0APK1 2017-06-12 2017-06-12 597.572 MiB
    SM-G130BU_1_20170610140700_22zi9o7iuj_fac.zip
    SM-G130BU
    ZTM Brazil
    		G130BU0APK1G130BUVJU0AQA1 2017-01-26 — — —
    SM-G130BU
    ZTO Brazil
    		G130BUZTO0APK1G130BUVJU0APK1 2017-06-12 2017-06-12 519.475 MiB
    SM-G130BU_1_20170610140653_kyc6o3f40k_fac.zip
    SM-G130BU
    ZTO Brazil
    		G130BU0APK1G130BUVJU0AQA1 2017-01-26 — — —

    No matching downloads

    Device specifications

    • Display diagonal8.89 cm (3.5")
    • Display resolution320 x 480 pixels
    • Display typeTFT
    • RAM0.5 GB
    • Rear camera resolution3 MP
    • Rear camera typeSingle camera
    • Battery capacity1300 mAh
    • Weight108 g

    Specifications of SM-G130, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    How to flash G130BUVJU0AQA1

    • G130BUVJU0AQA1 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    G130BUVJU0AQA1 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy Young2 Pro, released for Brazil (ZTM, ZTO). Samsung built it on 2017-01-26.

    Yes. G130BUVJU0AQA1 is the newest build for SM-G130BU on SamFirm. The previous build was G130BUVJU0APA1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Young2 Pro must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Young2 Pro running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Young2 Pro

    No changelog details available.
    No changelog details available.
    No changelog details available.
    Model firmware by region