SM-G360HU 2 countries Android 4.4.4 (KitKat)

Samsung Galaxy Core Prime G360HUXXU0APG1 Firmware

Name: Samsung Galaxy Core Prime (SM-G360HU)
Brand: Samsung
Availability: InStock

Samsung Galaxy Core Prime G360HUXXU0APG1 is an Android 4.4.4 (KitKat) firmware for Philippines (GLB, XTC, XTE), Thailand (THW). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G360HUXXU0AOK1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G360HU is available: G360HUXXU0AQI1.

8.7/10 (452)17,332 times

Android 4.4.4 (KitKat)

OS Version

2016-07-06

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: G360HUXXU0APG1

Model	Region	CSC Version	Size	File name
SM-G360HU	GLB Philippines	G360HUOLB0APF1	—	—
SM-G360HU	THW Thailand	G360HUOLB0APF1	—	—
SM-G360HU	XTC Philippines	G360HUOLB0APF1	—	—
SM-G360HU	XTE Philippines	G360HUOLB0APF1	—	—

Device specifications

Display diagonal11.4 cm (4.5")
Display resolution480 x 800 pixels
Display typeTFT
RAM1 GB
Rear camera resolution5 MP
Rear camera typeSingle camera
Battery capacity2000 mAh
Weight130 g

Specifications of SM-G360H, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash G360HUXXU0APG1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G360HUXXU0APG1 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G360HUXXU0APG1 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy Core Prime, released for Philippines (GLB, XTC, XTE), Thailand (THW). Samsung built it on 2016-07-06.

No. A newer build for SM-G360HU is available: G360HUXXU0AQI1. Install it instead of G360HUXXU0APG1 unless you need this exact version. The previous build was G360HUXXU0AOK1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Core Prime must be on bootloader binary 0 or lower.

This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Core Prime running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.