SM-G361HU 2 countries Android 5.1.1 (Lollipop)

Samsung Galaxy Core Prime G361HUXXS0API1 Firmware

Name: Samsung Galaxy Core Prime (SM-G361HU)
Brand: Samsung
Availability: InStock

Samsung Galaxy Core Prime G361HUXXS0API1 is an Android 5.1.1 (Lollipop) firmware for Philippines (XTC, XTE), Thailand (THW). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G361HUXXS0APE2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G361HU is available: G361HUXXS0AQD1.

8.9/10 (23)13,316 times

Android 5.1.1 (Lollipop)

OS Version

2016-09-15

First release

other regions until 2016-09-27

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

Model	Region	CSC Version	MODEM/CP Version	Build Date	Release date	Size	File name
SM-G361HU	THW Thailand	G361HUOLB0APA5	G361HUXXS0API1	2016-09-15	—	—	—
SM-G361HU	XTC, XTE Philippines	G361HUOLB0APA5	G361HUXXU0APA5	2016-09-27	2016-09-28	723.62 MiB	SM-G361HU_1_20160927171940_2idhc05qrs_fac.zip
SM-G361HU	XTC Philippines	G361HUOLB0APA5	G361HUXXS0API1	2016-09-15	—	—	—
SM-G361HU	XTE Philippines	G361HUOLB0APA5	G361HUXXS0API1	2016-09-15	—	—	—

Device specifications

Launched withAndroid 4.4.4
Display diagonal11.4 cm (4.5")
Display resolution800 x 480 pixels
Display typeTFT
RAM1 GB
Rear camera resolution5 MP
Rear camera typeSingle camera
Battery capacity2000 mAh
Weight131.3 g

Specifications of SM-G361F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash G361HUXXS0API1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G361HUXXS0API1 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G361HUXXS0API1 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy Core Prime, released for Philippines (XTC, XTE), Thailand (THW). Samsung built it on 2016-09-15.

No. A newer build for SM-G361HU is available: G361HUXXS0AQD1. Install it instead of G361HUXXS0API1 unless you need this exact version. The previous build was G361HUXXS0APE2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 723.62 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Core Prime must be on bootloader binary 0 or lower.

This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Core Prime running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 8 other builds of this model use the same binary, so you can switch between them in both directions.