SM-G390F 1 country Android 7.0 (Nougat)

Samsung Galaxy XCover4 G390FXXU1AQE3 Firmware

Name: Samsung Galaxy XCover4 (SM-G390F)
Brand: Samsung
Availability: InStock

Samsung Galaxy XCover4 G390FXXU1AQE3 is an Android 7.0 (Nougat) firmware for Netherlands (PHN). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G390FXXU1AQD7, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G390F is available: G390FXXU6CZC3.

9.1/10 (452)4,236 times

Android 7.0 (Nougat)

OS Version

2017-05-11

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy XCover4 use bootloader binary 6 (latest: G390FXXU6CZC3). If your device already runs binary 6, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: G390FXXU1AQE3

Model	Region	CSC Version	Size	File name	Download
SM-G390F	PHN Netherlands	G390F1AQE2	—	—

Device specifications

Launched withAndroid 7.0
Display diagonal12.7 cm (4.99")
Display resolution1280 x 720 pixels
Display typeTFT
Processor frequency1.4 GHz
RAM2 GB
RAM typeLPDDR3
Rear camera resolution13 MP
Rear camera typeSingle camera
Battery capacity2800 mAh
Weight172 g

How to flash G390FXXU1AQE3

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G390FXXU1AQE3 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G390FXXU1AQE3 is Android 7.0 (Nougat) firmware for Samsung Galaxy XCover4, released for Netherlands (PHN). Samsung built it on 2017-05-11.

No. A newer build for SM-G390F is available: G390FXXU6CZC3. Install it instead of G390FXXU1AQE3 unless you need this exact version. The previous build was G390FXXU1AQD7.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy XCover4 must be on bootloader binary 1 or lower.

This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy XCover4 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 25 other builds of this model use the same binary, so you can switch between them in both directions.