SM-G5308W 1 country Android 4.4.4 (KitKat)

Samsung Galaxy Grand Prime G5308WZMU1AOB1 Firmware

Name: Samsung Galaxy Grand Prime (SM-G5308W)
Brand: Samsung
Availability: InStock

Samsung Galaxy Grand Prime G5308WZMU1AOB1 is an Android 4.4.4 (KitKat) firmware for China (CHM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G5308WZHU1ANK2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G5308W is available: G5308WZHS1AQA2.

9.1/10 (452)4,417 times

Android 4.4.4 (KitKat)

OS Version

2015-02-13

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: G5308WZMU1AOB1

Model	Region	CSC Version	Size	File name	Download
SM-G5308W	CHM China	G5308W1AOB1	—	—

Device specifications

Display diagonal12.7 cm (5")
Display resolution540 x 960 pixels
Display typeTFT
RAM1.5 GB
Rear camera resolution8 MP
Rear camera typeSingle camera
Battery capacity2600 mAh
Weight156 g

Specifications of SM-G530, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash G5308WZMU1AOB1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G5308WZMU1AOB1 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G5308WZMU1AOB1 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy Grand Prime, released for China (CHM). Samsung built it on 2015-02-13.

No. A newer build for SM-G5308W is available: G5308WZHS1AQA2. Install it instead of G5308WZMU1AOB1 unless you need this exact version. The previous build was G5308WZHU1ANK2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Grand Prime must be on bootloader binary 1 or lower.

This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Grand Prime running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 13 other builds of this model use the same binary, so you can switch between them in both directions.

Other builds and changelog for Samsung Galaxy Grand Prime

G5308WZHS1AQA2 Oct 20, 2020

The exact changes may differ depending on your device model, country/Region, and service provider.

• Other bug fixes
- Network connectivity enhancement.
• The latest Android security patch has been applied.
- Device security has been further enhanced.

G5308WZMU1AQA2 Oct 15, 2020

The exact changes may differ depending on your device model, country/Region, and service provider.

• Other bug fixes
- Network connectivity enhancement.
• The latest Android security patch has been applied.
- Device security has been further enhanced.

G5308WZHS1APJ1 Oct 19, 2016