Samsung Galaxy Grand Prime G530BTVJS1APE1
SM-G530BT 1 country Android 4.4.4 (KitKat)

Samsung Galaxy Grand Prime G530BTVJS1APE1 Firmware

Samsung Galaxy Grand Prime G530BTVJS1APE1 is an Android 4.4.4 (KitKat) firmware for Brazil (ZTO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G530BTVJU1AOH2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G530BT is available: G530BTVJS1BRL1.

9.2/10 (454)4,433 times
Android 4.4.4 (KitKat)
OS Version
2016-05-05
Build Date
n/a
Security patch
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G530BTVJS1APE1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G530BT
    ZTO Brazil
    		G530BT1AOH2 — —

    No matching downloads

    How to flash G530BTVJS1APE1

    • G530BTVJS1APE1 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution540 x 960 pixels
    • Display typeTFT
    • RAM1.5 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • Battery capacity2600 mAh
    • Weight156 g

    Specifications of SM-G530, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G530BTVJS1APE1 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy Grand Prime, released for Brazil (ZTO). Samsung built it on 2016-05-05.

    No. A newer build for SM-G530BT is available: G530BTVJS1BRL1. Install it instead of G530BTVJS1APE1 unless you need this exact version. The previous build was G530BTVJU1AOH2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Grand Prime must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Grand Prime running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Grand Prime

    No changelog details available.
    Model firmware by region