SM-G570M 2 countries Android 8.0.0 (Oreo)

Samsung Galaxy J5 Prime G570MUBU6CSJ9 Firmware

Name: Samsung Galaxy J5 Prime (SM-G570M)
Brand: Samsung
Availability: InStock

Samsung Galaxy J5 Prime G570MUBU6CSJ9 is an Android 8.0.0 (Oreo) firmware for Argentina (PSN), Bolivia (BVO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G570MUBS6CSJ4 https://samfirm.shop/build/G570MUBS6CSJ4, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G570M is available: G570MUBS9CTJ3 https://samfirm.shop/build/G570MUBS9CTJ3.

9.1/10 (470)12,944 times

Android 8.0.0 (Oreo)

OS Version

2019-10-30

First release

other regions until 2019-11-09

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 6. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J5 Prime use bootloader binary 9 (latest: G570MUBS9CTJ3). If your device already runs binary 9, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

Model	Region	CSC Version	MODEM/CP Version	Build Date	Release date	Size	File name
SM-G570M	BVO Bolivia	G570MUUB6CSJ1	G570MUBU6CSJ1	2019-11-02	2019-11-20	2.196 GiB	SM-G570M_1_20201017003534_z027r5bk0x_fac.zip
SM-G570M	PSN Argentina	G570MPSN6CSJ9	G570MUBU6CSJ1	2019-11-09	2019-11-27	2.073 GiB	SM-G570M_1_20201028064635_fide6maz7e_fac.zip
SM-G570M	PSN Argentina	G570M6CSJ9	G570MUBU6CSJ9	2019-10-30	—	—	—

Device specifications

Display diagonal12.7 cm (5")
Display resolution1280 x 720 pixels
Display typeTFT
RAM2 GB
Rear camera resolution13 MP
Rear camera typeSingle camera
Battery capacity2400 mAh
Weight143 g

Specifications of SM-G570F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash G570MUBU6CSJ9

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G570MUBU6CSJ9 has bootloader binary 6. Your device must run binary 6 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G570MUBU6CSJ9 is Android 8.0.0 (Oreo) firmware for Samsung Galaxy J5 Prime, released for Argentina (PSN), Bolivia (BVO). Samsung built it on 2019-10-30.

No. A newer build for SM-G570M is available: G570MUBS9CTJ3. Install it instead of G570MUBU6CSJ9 unless you need this exact version. The previous build was G570MUBS6CSJ4.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J5 Prime must be on bootloader binary 6 or lower.

This build uses bootloader binary 6. It can be flashed on a Samsung Galaxy J5 Prime running binary 6 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.