SM-G920I 2 countries Android 6.0.1 (Marshmallow)

Samsung Galaxy S6 G920IDVS3EPIA Firmware

Name: Samsung Galaxy S6 (SM-G920I)
Brand: Samsung
Availability: InStock

Samsung Galaxy S6 G920IDVS3EPIA is an Android 6.0.1 (Marshmallow) firmware for Chile (CHT), Mexico (TMM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G920IDVS3EPI9 https://samfirm.shop/build/G920IDVS3EPI9, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G920I is available: G920IDVU4FVHQ https://samfirm.shop/build/G920IDVU4FVHQ.

9.3/10 (453)8,730 times

Android 6.0.1 (Marshmallow)

OS Version

2016-09-09

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S6 use bootloader binary 4 (latest: G920IDVU4FVHQ). If your device already runs binary 4, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

Model	Region	CSC Version	MODEM/CP Version	Release date	Size	File name	Download
SM-G920I	CHT Chile	G920ITFG3EPE4	G920IDVU3EPI5	2016-10-08	2.441 GiB	SM-G920I_1_20221014150421_z9u995nv7w_fac.zip
SM-G920I	TMM Mexico	G920ITFG3EPE4	G920IDVS3EPIA	—	—	—

Device specifications

Launched withAndroid 5.0
Display diagonal12.9 cm (5.1")
Display resolution2560 x 1440 pixels
Display typeSAMOLED
RAM3 GB
Rear camera resolution16 MP
Rear camera typeSingle camera
Battery capacity2550 mAh
Weight138 g

Specifications of SM-G920F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash G920IDVS3EPIA

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G920IDVS3EPIA has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G920IDVS3EPIA is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy S6, released for Chile (CHT), Mexico (TMM). Samsung built it on 2016-09-09.

No. A newer build for SM-G920I is available: G920IDVU4FVHQ. Install it instead of G920IDVS3EPIA unless you need this exact version. The previous build was G920IDVS3EPI9.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.441 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S6 must be on bootloader binary 3 or lower.

This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy S6 running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 152 other builds of this model use the same binary, so you can switch between them in both directions.