Samsung Galaxy S6 G920T1UVU5EPK6
SM-G920T1 1 country Android 6.0.1 (Nougat)

Samsung Galaxy S6 G920T1UVU5EPK6 Firmware

Samsung Galaxy S6 G920T1UVU5EPK6 is an Android 6.0.1 (Nougat) firmware for United States (TMB). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G920T1UVS4EPH3: bootloader binary raised from 4 to 5, so after installing it there is no way back to older builds. A newer build for SM-G920T1 is available: G920T1UVU6FVG1.

9.1/10 (455)4,373 times
Android 6.0.1 (Nougat)
OS Version
2016-11-16
Build Date
n/a
Security patch
1
Countries
1
CSC codes
5
Bootloader binary

Bootloader binary 5. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S6 use bootloader binary 6 (latest: G920T1UVU6FVG1). If your device already runs binary 6, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G920T1UVU5EPK6
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G920T1
    TMB United States
    		G920T15EPK6 — —

    No matching downloads

    How to flash G920T1UVU5EPK6

    • G920T1UVU5EPK6 has bootloader binary 5. Your device must run binary 5 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 5.0
    • Display diagonal12.9 cm (5.1")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • RAM3 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • Battery capacity2550 mAh
    • Weight138 g

    Specifications of SM-G920T, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G920T1UVU5EPK6 is Android 6.0.1 (Nougat) firmware for Samsung Galaxy S6, released for United States (TMB). Samsung built it on 2016-11-16.

    No. A newer build for SM-G920T1 is available: G920T1UVU6FVG1. Install it instead of G920T1UVU5EPK6 unless you need this exact version. The previous build was G920T1UVS4EPH3.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S6 must be on bootloader binary 5 or lower.

    This build uses bootloader binary 5. It can be flashed on a Samsung Galaxy S6 running binary 5 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 6 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S6

    • GPS
    The stability has been improved.

    No changelog details available.
    Model firmware by region