SM-G920T 1 country Android 6.0.1 (Nougat)

Samsung Galaxy S6 G920TUES5DPI2 Firmware

Name: Samsung Galaxy S6 (SM-G920T)
Brand: Samsung
Availability: InStock

Samsung Galaxy S6 G920TUES5DPI2 is an Android 6.0.1 (Nougat) firmware for United States (XAR). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G920TUVS4EPH2 https://samfirm.shop/build/G920TUVS4EPH2: bootloader binary raised from 4 to 5, so after installing it there is no way back to older builds. A newer build for SM-G920T is available: G920TUVU6FVH1 https://samfirm.shop/build/G920TUVU6FVH1.

9.0/10 (453)4,200 times

Android 6.0.1 (Nougat)

OS Version

2016-09-12

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 5. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S6 use bootloader binary 6 (latest: G920TUVU6FVH1). If your device already runs binary 6, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: G920TUES5DPI2

Model	Region	CSC Version	Size	File name	Download
SM-G920T	XAR United States	G920T5DPI2	—	—

Device specifications

Launched withAndroid 5.0
Display diagonal12.9 cm (5.1")
Display resolution2560 x 1440 pixels
Display typeSAMOLED
Processor frequency2.1 GHz
Processor familySamsung Exynos
Processor model7 Octa 7420
RAM3 GB
Rear camera resolution16 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity2550 mAh
Weight138 g

How to flash G920TUES5DPI2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G920TUES5DPI2 has bootloader binary 5. Your device must run binary 5 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G920TUES5DPI2 is Android 6.0.1 (Nougat) firmware for Samsung Galaxy S6, released for United States (XAR). Samsung built it on 2016-09-12.

No. A newer build for SM-G920T is available: G920TUVU6FVH1. Install it instead of G920TUES5DPI2 unless you need this exact version. The previous build was G920TUVS4EPH2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S6 must be on bootloader binary 5 or lower.

This build uses bootloader binary 5. It can be flashed on a Samsung Galaxy S6 running binary 5 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 20 other builds of this model use the same binary, so you can switch between them in both directions.