SM-G9287C 4 countries Android 7.0 (Nougat)

Samsung Galaxy S6 Edge+ G9287CDXU3CQH2 Firmware

Name: Samsung Galaxy S6 Edge+ (SM-G9287C)
Brand: Samsung
Availability: InStock

Samsung Galaxy S6 Edge+ G9287CDXU3CQH2 is an Android 7.0 (Nougat) firmware for 4 countries, 6 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G9287CDXS3CQH1: Android updated from Android 7.0 (Lollipop) to Android 7.0 (Nougat). A newer build for SM-G9287C is available: G9287CDXU5CVG1.

9.3/10 (451)26,129 times

Android 7.0 (Nougat)

OS Version

2017-08-21

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S6 Edge+ use bootloader binary 5 (latest: G9287CDXU5CVG1). If your device already runs binary 5, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: G9287CDXU3CQH2

Model	Region	CSC Version	Size	File name
SM-G9287C	GLB Philippines	G9287COLB3CQH2	—	—
SM-G9287C	MYM Myanmar (Burma)	G9287COLB3CQH2	—	—
SM-G9287C	SMA Philippines	G9287COLB3CQH2	—	—
SM-G9287C	XID Indonesia	G9287COLB3CQH2	—	—
SM-G9287C	XME Malaysia	G9287COLB3CQH2	—	—
SM-G9287C	XTC Philippines	G9287COLB3CQH2	—	—

Device specifications

Launched withAndroid 5.1
Display diagonal14.5 cm (5.7")
Display resolution2560 x 1440 pixels
Display typeSAMOLED
RAM4 GB
Rear camera resolution16 MP
Rear camera typeSingle camera
Battery capacity3000 mAh
Weight153 g

Specifications of SM-G928, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash G9287CDXU3CQH2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G9287CDXU3CQH2 has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G9287CDXU3CQH2 is Android 7.0 (Nougat) firmware for Samsung Galaxy S6 Edge+, released for 4 countries, 6 CSC codes. Samsung built it on 2017-08-21.

No. A newer build for SM-G9287C is available: G9287CDXU5CVG1. Install it instead of G9287CDXU3CQH2 unless you need this exact version. The previous build was G9287CDXS3CQH1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S6 Edge+ must be on bootloader binary 3 or lower.

This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy S6 Edge+ running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 14 other builds of this model use the same binary, so you can switch between them in both directions.

Other builds and changelog for Samsung Galaxy S6 Edge+

G9287CDXU5CVG1 Aug 20, 2022

• GPS
The stability has been improved.
• Security
The device is protected with improved security.

G9287CDXS5CRH1 Aug 6, 2018