Samsung Galaxy S6 Edge+ G928CXXU3CQH4 Firmware
Samsung Galaxy S6 Edge+ G928CXXU3CQH4 is an Android 7.0 (Nougat) firmware for Cambodia (CAM), Thailand (THL), Vietnam (XXV). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G928CXXU3CQH3: Android updated from Android 7.0 (Marshmallow) to Android 7.0 (Nougat). A newer build for SM-G928C is available: G928CXXU5CVG4.
9.3/10 (452)12,974 times
Android 7.0 (Nougat)
OS Version
2017-08-21
Build Date
n/a
Security patch
3
Countries
3
CSC codes
3
Bootloader binary
Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy S6 Edge+ use bootloader binary 5 (latest: G928CXXU5CVG4). If your device already runs binary 5, this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
MODEM/CP Version: G928CXXU3CQH4
Device specifications
- Launched withAndroid 5.1
- Display diagonal14.5 cm (5.7")
- Display resolution2560 x 1440 pixels
- Display typeSAMOLED
- Processor frequency2.1 GHz
- Processor familySamsung Exynos
- Processor model7 Octa 7420
- RAM4 GB
- Rear camera resolution16 MP
- Rear camera typeSingle camera
- SIM cardsSingle SIM
- Battery capacity3000 mAh
- Weight153 g
How to flash G928CXXU3CQH4
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- G928CXXU3CQH4 has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
G928CXXU3CQH4 is Android 7.0 (Nougat) firmware for Samsung Galaxy S6 Edge+, released for Cambodia (CAM), Thailand (THL), Vietnam (XXV). Samsung built it on 2017-08-21.
No. A newer build for SM-G928C is available: G928CXXU5CVG4. Install it instead of G928CXXU3CQH4 unless you need this exact version. The previous build was G928CXXU3CQH3.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S6 Edge+ must be on bootloader binary 3 or lower.
This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy S6 Edge+ running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 39 other builds of this model use the same binary, so you can switch between them in both directions.