SM-G930F 1 country Android 7.0 (Oreo)

Samsung Galaxy S7 G930FXXS1DRA4 Firmware

Name: Samsung Galaxy S7 (SM-G930F)
Brand: Samsung
Availability: InStock

Samsung Galaxy S7 G930FXXS1DRA4 is an Android 7.0 (Oreo) firmware for Luxembourg (LUX). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G930FXXU1DRA2: Android updated from Android 7.0 (Nougat) to Android 7.0 (Oreo). A newer build for SM-G930F is available: G930FXXU8EZCD.

9.2/10 (453)8,669 times

Android 7.0 (Oreo)

OS Version

2018-01-11

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S7 use bootloader binary 8 (latest: G930FXXU8EZCD). If your device already runs binary 8, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Model	Region	CSC Version	MODEM/CP Version	Release date	Size	File name	Download
SM-G930F	LUX Luxembourg	G930F1DQL1	G930FXXS1DRA4	—	—	—
SM-G930F	LUX Luxembourg	G930FLUX1DQL1	G930FXXU1DRA3	2018-01-29	2.207 GiB	SM-G930F_1_20220814164210_txmrwbkov7_fac.zip

Device specifications

Launched withAndroid 6.0
Display diagonal12.9 cm (5.1")
Display resolution2560 x 1440 pixels
Display typeSAMOLED
Processor frequency2.3 GHz
Processor familySamsung Exynos
RAM4 GB
RAM typeLPDDR4
Rear camera resolution12 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity3000 mAh
Weight152 g

How to flash G930FXXS1DRA4

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G930FXXS1DRA4 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G930FXXS1DRA4 is Android 7.0 (Oreo) firmware for Samsung Galaxy S7, released for Luxembourg (LUX). Samsung built it on 2018-01-11.

No. A newer build for SM-G930F is available: G930FXXU8EZCD. Install it instead of G930FXXS1DRA4 unless you need this exact version. The previous build was G930FXXU1DRA2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.207 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S7 must be on bootloader binary 1 or lower.

This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy S7 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 229 other builds of this model use the same binary, so you can switch between them in both directions.