Samsung Galaxy S7 G930LKLU2ERJ1
SM-G930L 1 country Android 8.0.0 (Oreo)

Samsung Galaxy S7 G930LKLU2ERJ1 Firmware

Samsung Galaxy S7 G930LKLU2ERJ1 is an Android 8.0.0 (Oreo) firmware for South Korea (LUC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G930LKLU1ERG2: bootloader binary raised from 1 to 2, so after installing it there is no way back to older builds. A newer build for SM-G930L is available: G930LKLU3EVG2.

9.2/10 (454)4,435 times
Android 8.0.0 (Oreo)
OS Version
2018-10-16
Build Date
n/a
Security patch
1
Countries
1
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S7 use bootloader binary 3 (latest: G930LKLU3EVG2). If your device already runs binary 3, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G930LKLU2ERJ1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G930L
    LUC South Korea
    		G930L2ERJ1 — —

    No matching downloads

    How to flash G930LKLU2ERJ1

    • G930LKLU2ERJ1 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 6.0
    • Display diagonal12.9 cm (5.1")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • RAM4 GB
    • RAM typeLPDDR4
    • Rear camera resolution12 MP
    • Rear camera typeSingle camera
    • Battery capacity3000 mAh
    • Weight152 g

    Specifications of SM-G930F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G930LKLU2ERJ1 is Android 8.0.0 (Oreo) firmware for Samsung Galaxy S7, released for South Korea (LUC). Samsung built it on 2018-10-16.

    No. A newer build for SM-G930L is available: G930LKLU3EVG2. Install it instead of G930LKLU2ERJ1 unless you need this exact version. The previous build was G930LKLU1ERG2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S7 must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy S7 running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 4 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S7

    No changelog details available.
    Model firmware by region