SM-G930P 1 country Android 8.0.0 (Oreo)

Samsung Galaxy S7 G930PVPSBCTA1 Firmware

Name: Samsung Galaxy S7 (SM-G930P)
Brand: Samsung
Availability: InStock

Samsung Galaxy S7 G930PVPSBCTA1 is an Android 8.0.0 (Oreo) firmware for United States (BST, SPR, VMU, XAS). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G930PVPUACSJ3: bootloader binary raised from A (10) to B (11), so after installing it there is no way back to older builds. This is the newest build for SM-G930P.

8.9/10 (469)16,998 times

Android 8.0.0 (Oreo)

OS Version

2020-01-21

Build Date

n/a

Security patch

Countries

CSC codes

B (11)

Bootloader binary

Bootloader binary B (11). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: G930PVPSBCTA1

Model	Region	CSC Version	Release date	Size	File name	Download
SM-G930P	BST, SPR, VMU, XAS United States	G930PSPTBCTA1	2020-02-06	3.13 GiB	SM-G930P_1_20200121112555_jqjvgeu1gf_fac.zip MD5:fb2d24c2d1dcd612c4bace815b8591ce SHA1:ddb0ad1a945d28eb2b91b38a2921b95490f734aa

Device specifications

Launched withAndroid 6.0
Display diagonal12.9 cm (5.1")
Display resolution2560 x 1440 pixels
Display typeSAMOLED
RAM4 GB
RAM typeLPDDR4
Rear camera resolution12 MP
Rear camera typeSingle camera
Battery capacity3000 mAh
Weight152 g

Specifications of SM-G930F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash G930PVPSBCTA1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G930PVPSBCTA1 has bootloader binary B (11). Your device must run binary B (11) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G930PVPSBCTA1 is Android 8.0.0 (Oreo) firmware for Samsung Galaxy S7, released for United States (BST, SPR, VMU, XAS). Samsung built it on 2020-01-21.

Yes. G930PVPSBCTA1 is the newest build for SM-G930P on SamFirm. The previous build was G930PVPUACSJ3.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 3.13 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S7 must be on bootloader binary B (11) or lower.

This build uses bootloader binary B (11). It can be flashed on a Samsung Galaxy S7 running binary B (11) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". No other build of this model uses binary B (11).