Samsung Galaxy S7 G930W8VLU1APB7
SM-G930W8 1 country Android 6.0.1 (Marshmallow)

Samsung Galaxy S7 G930W8VLU1APB7 Firmware

Samsung Galaxy S7 G930W8VLU1APB7 is an Android 6.0.1 (Marshmallow) firmware for Canada (BWA, ESK, FMC, GLW, KDO, MTA, RWC, TLS, VMC, VTR, XAC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. A newer build for SM-G930W8 is available: G930W8VLU8CVG1.

8.8/10 (453)48,114 times
Android 6.0.1 (Marshmallow)
OS Version
2016-02-11
Build Date
n/a
Security patch
1
Countries
11
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S7 use bootloader binary 8 (latest: G930W8VLU8CVG1). If your device already runs binary 8, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G930W8VLU1APB7
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G930W8
    BWA, ESK, FMC, GLW, KDO, MTA, RWC, TLS, VMC, VTR, XAC Canada
    		G930W8OYA1APB7 2016-03-12 2.376 GiB
    SM-G930W8_1_20220801191151_ng53idqa6s_fac.zip
    MD5:ec95c8394966132ddd7e83a1194f1fac
    SHA1:2b4d14161af83784903f0b9632e7d31cfd4389a7

    No matching downloads

    Device specifications

    • Launched withAndroid 6.0
    • Display diagonal12.9 cm (5.1")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • RAM4 GB
    • RAM typeLPDDR4
    • Rear camera resolution12 MP
    • Rear camera typeSingle camera
    • Battery capacity3000 mAh
    • Weight152 g

    Specifications of SM-G930W, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Rollout of G930W8VLU1APB7 by region

    Samsung released this build in all regions (11) on the same day, March 12, 2016.

    How to flash G930W8VLU1APB7

    • G930W8VLU1APB7 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    G930W8VLU1APB7 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy S7, released for Canada (BWA, ESK, FMC, GLW, KDO, MTA, RWC, TLS, VMC, VTR, XAC). Samsung built it on 2016-02-11.

    No. A newer build for SM-G930W8 is available: G930W8VLU8CVG1. Install it instead of G930W8VLU1APB7 unless you need this exact version.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.376 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S7 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy S7 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S7

    No changelog details available.

    · The security of your device has been improved.

    No changelog details available.
    Model firmware by region