Samsung Galaxy W I8150ZSLM4D
GT-I8150 2 countries Android 2.3.6 (Gingerbread)

Samsung Galaxy W I8150ZSLM4D Firmware

Samsung Galaxy W I8150ZSLM4D is an Android 2.3.6 (Gingerbread) firmware for FET, Hong Kong SAR China (TGY). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I8150JPLC1T: bootloader binary raised from P (25) to S (28), so after installing it there is no way back to older builds. A newer build for GT-I8150 is available: I8150ZSLM4.

8.9/10 (453)8,701 times
Android 2.3.6 (Gingerbread)
OS Version
n/a
Build Date
n/a
Security patch
2
Countries
2
CSC codes
S (28)
Bootloader binary

Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy W use bootloader binary Z (35) (latest: I8150ZSLM4). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: I8150ZSLM4
    ModelRegionCSC VersionSizeFile nameDownload
    GT-I8150
    FET
    		I8150OZSLM4 — —
    GT-I8150
    TGY Hong Kong SAR China
    		I8150OZSLM4 — —

    No matching downloads

    How to flash I8150ZSLM4D

    • I8150ZSLM4D has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 2.3
    • Display diagonal9.4 cm (3.7")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • Processor frequency1.4 GHz
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity1500 mAh
    • Weight114.7 g

    Frequently Asked Questions

    I8150ZSLM4D is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy W, released for FET, Hong Kong SAR China (TGY).

    No. A newer build for GT-I8150 is available: I8150ZSLM4. Install it instead of I8150ZSLM4D unless you need this exact version. The previous build was I8150JPLC1T.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy W must be on bootloader binary S (28) or lower.

    This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy W running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". No other build of this model uses binary S (28).

    Other builds and changelog for Samsung Galaxy W

    No changelog details available.
    Model firmware by region