GT-I8190 3 countries Android 4.1.2 (Jelly Bean)

Samsung Galaxy S Ⅲ mini I8190DXAML1 Firmware

Name: Samsung Galaxy S Ⅲ mini (GT-I8190)
Brand: Samsung
Availability: InStock

Samsung Galaxy S Ⅲ mini I8190DXAML1 is an Android 4.1.2 (Jelly Bean) firmware for Indonesia (XSE), Philippines (GLB, SMA, XTC, XTE), Vietnam (XEV, XXV). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I8190XXAMJ3 https://samfirm.shop/build/I8190XXAMJ3: Android updated from Jelly(Android Bean) to Android 4.1.2 (Jelly Bean). A newer build for GT-I8190 is available: I8190XXAOR1 https://samfirm.shop/build/I8190XXAOR1.

9.1/10 (471)30,247 times

Android 4.1.2 (Jelly Bean)

OS Version

2014-01-29

Build Date

n/a

Security patch

Countries

CSC codes

X (33)

Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: I8190DXAML1

Model	Region	CSC Version	Build Date	Release date	Size	File name
GT-I8190	GLB Philippines	I8190QLBAML1	—	—	—	—
GT-I8190	SMA Philippines	I8190QLBAML1	—	—	—	—
GT-I8190	XEV Vietnam	I8190QLBAML1	2014-01-29	2014-01-29	—	—
GT-I8190	XSE Indonesia	I8190QLBAML1	2014-01-29	2014-01-29	—	—
GT-I8190	XTC Philippines	I8190QLBAML1	2014-01-29	2014-01-29	—	—
GT-I8190	XTE Philippines	I8190QLBAML1	—	—	—	—
GT-I8190	XXV Vietnam	I8190QLBAML1	2014-01-29	2014-01-29	—	—

Device specifications

Launched withAndroid 4.1
Display diagonal10.2 cm (4")
Display resolution800 x 480 pixels
Display typeSAMOLED
Processor frequency1 GHz
RAM1 GB
Rear camera resolution5 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity1500 mAh
Weight120 g

How to flash I8190DXAML1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

I8190DXAML1 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

I8190DXAML1 is Android 4.1.2 (Jelly Bean) firmware for Samsung Galaxy S Ⅲ mini, released for Indonesia (XSE), Philippines (GLB, SMA, XTC, XTE), Vietnam (XEV, XXV). Samsung built it on 2014-01-29.

No. A newer build for GT-I8190 is available: I8190XXAOR1. Install it instead of I8190DXAML1 unless you need this exact version. The previous build was I8190XXAMJ3.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S Ⅲ mini must be on bootloader binary X (33) or lower.

This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy S Ⅲ mini running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 20 other builds of this model use the same binary, so you can switch between them in both directions.