Samsung GALAXY S CLEAR LCD I9003LUBKC2
GT-I9003L 2 countries Android 2.2.1 (Froyo)

Samsung GALAXY S CLEAR LCD I9003LUBKC2 Firmware

Samsung GALAXY S CLEAR LCD I9003LUBKC2 is an Android 2.2.1 (Froyo) firmware for Chile (CHL), Uruguay (UPO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9003LUBKB1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-I9003L is available: I9003LUBLH1.

9.0/10 (471)8,454 times
Android 2.2.1 (Froyo)
OS Version
2011-03-25
Build Date
n/a
Security patch
2
Countries
2
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: UBKC2
    ModelRegionCSC VersionSizeFile nameDownload
    GT-I9003L
    CHL Chile
    		I9003LUBKC2 — —
    GT-I9003L
    UPO Uruguay
    		I9003LUBKC2 — —

    No matching downloads

    How to flash I9003LUBKC2

    • I9003LUBKC2 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    I9003LUBKC2 is Android 2.2.1 (Froyo) firmware for Samsung GALAXY S CLEAR LCD, released for Chile (CHL), Uruguay (UPO). Samsung built it on 2011-03-25.

    No. A newer build for GT-I9003L is available: I9003LUBLH1. Install it instead of I9003LUBKC2 unless you need this exact version. The previous build was I9003LUBKB1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung GALAXY S CLEAR LCD must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung GALAXY S CLEAR LCD running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung GALAXY S CLEAR LCD

    No changelog details available.
    No changelog details available.
    No changelog details available.
    No changelog details available.
    Model firmware by region