GT-I9060I 4 countries Android 4.4.4 (KitKat)

Samsung Galaxy Grand NEO I9060IXMS0AQD2 Firmware

Name: Samsung Galaxy Grand NEO (GT-I9060I)
Brand: Samsung
Availability: InStock

Samsung Galaxy Grand NEO I9060IXMS0AQD2 is an Android 4.4.4 (KitKat) firmware for 4 countries, 5 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9060IXXS0AQC2 https://samfirm.shop/build/I9060IXXS0AQC2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-I9060I is available: I9060IXXS0AQD8 https://samfirm.shop/build/I9060IXXS0AQD8.

9.2/10 (452)21,628 times

Android 4.4.4 (KitKat)

OS Version

n/a

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

Model	Region	CSC Version	MODEM/CP Version	Size	File name
GT-I9060I	ATO Austria	I9060IATO0AOG1	I9060IXMU0AOI1	—	—
GT-I9060I	DRE Austria	I9060IDRE0AOJ1	I9060IXMU0AOI1	—	—
GT-I9060I	LUX Luxembourg	I9060ILUX0AOG1	I9060IXMU0AOI1	—	—
GT-I9060I	PHN Netherlands	I9060IPHN0AOG1	I9060IXMU0AOI1	—	—
GT-I9060I	TSI Ireland	I9060ITSI0AOG1	I9060IXMU0AOG2	—	—

Device specifications

Display diagonal12.7 cm (5")
Display resolution480 x 800 pixels
Display typeTFT
Processor frequency1.2 GHz
RAM1 GB
Rear camera resolution5 MP
Rear camera typeSingle camera
SIM cardsDual SIM
Battery capacity2100 mAh
Weight160 g

How to flash I9060IXMS0AQD2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

I9060IXMS0AQD2 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

I9060IXMS0AQD2 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy Grand NEO, released for 4 countries, 5 CSC codes.

No. A newer build for GT-I9060I is available: I9060IXXS0AQD8. Install it instead of I9060IXMS0AQD2 unless you need this exact version. The previous build was I9060IXXS0AQC2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Grand NEO must be on bootloader binary 0 or lower.

This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Grand NEO running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 62 other builds of this model use the same binary, so you can switch between them in both directions.