GT-I9103 1 country Android 2.3.5 (Gingerbread)

Samsung Galaxy R I9103JPLPD Firmware

Name: Samsung Galaxy R (GT-I9103)
Brand: Samsung
Availability: InStock

Samsung Galaxy R I9103JPLPD is an Android 2.3.5 (Gingerbread) firmware for United Arab Emirates (XSG). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9103JPKI3 https://samfirm.shop/build/I9103JPKI3, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-I9103 is available: I9103ZSLPE https://samfirm.shop/build/I9103ZSLPE.

9.0/10 (451)4,185 times

Android 2.3.5 (Gingerbread)

OS Version

n/a

Build Date

n/a

Security patch

Countries

CSC codes

J (19)

Bootloader binary

Bootloader binary J (19). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy R use bootloader binary Z (35) (latest: I9103ZSLPE). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: I9103XXLQ3

Model	Region	CSC Version	Size	File name	Download
GT-I9103	XSG United Arab Emirates	I9103OJPLPA	—	—

Device specifications

Launched withAndroid 2.3
Display diagonal10.6 cm (4.19")
Display resolution800 x 480 pixels
Display typeAMOLED
Processor frequency1 GHz
Rear camera resolution5 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity1650 mAh
Weight132 g

How to flash I9103JPLPD

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

I9103JPLPD has bootloader binary J (19). Your device must run binary J (19) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

I9103JPLPD is Android 2.3.5 (Gingerbread) firmware for Samsung Galaxy R, released for United Arab Emirates (XSG).

No. A newer build for GT-I9103 is available: I9103ZSLPE. Install it instead of I9103JPLPD unless you need this exact version. The previous build was I9103JPKI3.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy R must be on bootloader binary J (19) or lower.

This build uses bootloader binary J (19). It can be flashed on a Samsung Galaxy R running binary J (19) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.