GT-I9300I 1 country Android 4.4.4 (Jelly)

Samsung Galaxy S3 Neo I9300IXWUBNJ1 Firmware

Name: Samsung Galaxy S3 Neo (GT-I9300I)
Brand: Samsung
Availability: InStock

Samsung Galaxy S3 Neo I9300IXWUBNJ1 is an Android 4.4.4 (Jelly) firmware for Russia (SER). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9300IZHUBNI2 https://samfirm.shop/build/I9300IZHUBNI2: Android updated from Android 4.4.4 (KitKat) to Android 4.4.4 (Jelly). A newer build for GT-I9300I is available: I9300IDDUBQE2 https://samfirm.shop/build/I9300IDDUBQE2.

9.1/10 (452)4,441 times

Android 4.4.4 (Jelly)

OS Version

2014-10-22

Build Date

n/a

Security patch

Countries

CSC codes

U (30)

Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: I9300IXWUBNJ1

Model	Region	CSC Version	Size	File name	Download
GT-I9300I	SER Russia	I9300IOXEBNJ1	—	—

Device specifications

Display diagonal12.2 cm (4.8")
Display resolution720 x 1280 pixels
Display typeSAMOLED
Processor frequency1.4 GHz
RAM1.5 GB
Rear camera resolution8 MP
Rear camera typeSingle camera
SIM cardsDual SIM
Battery capacity2100 mAh
Weight132 g

How to flash I9300IXWUBNJ1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

I9300IXWUBNJ1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

I9300IXWUBNJ1 is Android 4.4.4 (Jelly) firmware for Samsung Galaxy S3 Neo, released for Russia (SER). Samsung built it on 2014-10-22.

No. A newer build for GT-I9300I is available: I9300IDDUBQE2. Install it instead of I9300IXWUBNJ1 unless you need this exact version. The previous build was I9300IZHUBNI2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S3 Neo must be on bootloader binary U (30) or lower.

This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S3 Neo running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 47 other builds of this model use the same binary, so you can switch between them in both directions.