Samsung Galaxy S 4 (Snapdragon) I9505XXUGNH2
GT-I9505 2 countries Android 4.4.2 (KitKat)

Samsung Galaxy S 4 (Snapdragon) I9505XXUGNH2 Firmware

Samsung Galaxy S 4 (Snapdragon) I9505XXUGNH2 is an Android 4.4.2 (KitKat) firmware for Poland (PLS), Sweden (VDS). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9505VJUGNH1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-I9505 is available: I9505XXUPQG1.

9.0/10 (472)8,532 times
Android 4.4.2 (KitKat)
OS Version
2014-08-04
Build Date
n/a
Security patch
2
Countries
2
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: I9505XXUGNH2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    GT-I9505
    PLS Poland
    		I9505PLSGNH1 2014-11-10 1.579 GiB
    GT-I9505_1_20170315191826_l8vhytfae9_fac.zip
    GT-I9505
    VDS Sweden
    		I9505VDSGNH1 2014-12-30 1.485 GiB
    GT-I9505_1_20170620144040_fpq6f2z2hl_fac.zip

    No matching downloads

    How to flash I9505XXUGNH2

    • I9505XXUGNH2 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of I9505XXUGNH2 by region

    First release
    November 10, 2014
    Last region
    December 30, 2014
    Duration
    51 days
    Regions
    2
    1. Day 1 · · 1 region
      PolandPLS
    2. Day 51 · · 1 region
      SwedenVDS

    Device specifications

    • Launched withAndroid 4.2.2
    • Display diagonal12.7 cm (5")
    • Display resolution1080 x 1920 pixels
    • Display typeAMOLED
    • Processor frequency1.9 GHz
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity2600 mAh
    • Weight130 g

    Frequently Asked Questions

    I9505XXUGNH2 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy S 4 (Snapdragon), released for Poland (PLS), Sweden (VDS). Samsung built it on 2014-08-04.

    No. A newer build for GT-I9505 is available: I9505XXUPQG1. Install it instead of I9505XXUGNH2 unless you need this exact version. The previous build was I9505VJUGNH1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S 4 (Snapdragon) must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S 4 (Snapdragon) running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 101 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S 4 (Snapdragon)

    No changelog details available.
    Model firmware by region