Samsung Galaxy J1 J100HXCS0APL3 Firmware
Samsung Galaxy J1 J100HXCS0APL3 is an Android 4.4.4 (KitKat) firmware for Austria (ATO), Portugal (MEO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J100HXCS0APL2 https://samfirm.shop/build/J100HXCS0APL2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J100H is available: J100HXXU0AQK1 https://samfirm.shop/build/J100HXXU0AQK1.
9.1/10 (39)8,974 times
Android 4.4.4 (KitKat)
OS Version
2016-12-23
First release
other regions until 2017-03-21
n/a
Security patch
2
Countries
2
CSC codes
0
Bootloader binary
Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
No matching downloads
How to flash J100HXCS0APL3
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- J100HXCS0APL3 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Rollout of J100HXCS0APL3 by region
- First release
- February 28, 2017
- Last region
- March 22, 2017
- Duration
- 23 days
- Regions
- 2
- Day 1 · · 1 regionAustriaATO
- Day 23 · · 1 regionPortugalMEO
Device specifications
- Display diagonal10.9 cm (4.3")
- Display resolution480 x 800 pixels
- Display typeTFT
- Processor frequency1.2 GHz
- RAM0.5 GB
- Rear camera resolution5 MP
- Rear camera typeSingle camera
- Battery capacity1850 mAh
- Weight122 g
Frequently Asked Questions
J100HXCS0APL3 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy J1, released for Austria (ATO), Portugal (MEO). Samsung built it on 2016-12-23.
No. A newer build for SM-J100H is available: J100HXXU0AQK1. Install it instead of J100HXCS0APL3 unless you need this exact version. The previous build was J100HXCS0APL2.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J1 must be on bootloader binary 0 or lower.
This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy J1 running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 94 other builds of this model use the same binary, so you can switch between them in both directions.
Other builds and changelog for Samsung Galaxy J1
No changelog details available.
- J100HXXU0AQK1
- J100HXCU0AQE2May 18, 2017
- J100HXXS0AQD2Apr 27, 2017
- J100HXCU0AQD1Apr 3, 2017
- J100HXCS0AQC7Mar 27, 2017
- J100HXCS0AQC6Mar 21, 2017
- J100HXCS0AQC4Mar 17, 2017
- J100HXCS0AQC3Mar 17, 2017
- J100HXCS0AQC2Mar 7, 2017
- J100HXXS0AQC2Mar 22, 2017
- J100HXXS0AQC1Mar 10, 2017
- J100HDDS0AQB1Feb 14, 2017
- J100HXXS0AQB1Feb 27, 2017
- J100HXXU0AQB1Feb 2, 2017
- J100HDDU0AQA2Jan 11, 2017
- J100HXXU0AQA2Jan 13, 2017
- J100HXCU0AQA1Jan 9, 2017
- J100HXXU0AQA1Jan 4, 2017
- J100HXCS0APL3Dec 23, 2016
- J100HXCS0APL2Dec 23, 2016