SM-J106M 2 countries Android 6.0.1 (Marshmallow)

Samsung Galaxy J1 Mini Prime J106MUBS0ARD1 Firmware

Name: Samsung Galaxy J1 Mini Prime (SM-J106M)
Brand: Samsung
Availability: InStock

Samsung Galaxy J1 Mini Prime J106MUBS0ARD1 is an Android 6.0.1 (Marshmallow) firmware for Fiji (VFJ), Papua New Guinea (PNG). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J106MUBU0ARD1 https://samfirm.shop/build/J106MUBU0ARD1: Android updated from Android 6.0.1 to Android 6.0.1 (Marshmallow). A newer build for SM-J106M is available: J106MUBU0ARL2 https://samfirm.shop/build/J106MUBU0ARL2.

9.0/10 (454)17,252 times

Android 6.0.1 (Marshmallow)

OS Version

2018-04-04

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

Model	Region	CSC Version	MODEM/CP Version	Release date	Size	File name
SM-J106M	PNG Papua New Guinea	J106M0AQK1	J106MUBS0ARD1	—	—	—
SM-J106M	PNG Papua New Guinea	J106MPNG0AQK1	J106MUBU0AQF1	2018-05-10	1.267 GiB	SM-J106M_1_20180518185814_vl4xz0aarw_fac.zip
SM-J106M	VFJ Fiji	J106M0AQK1	J106MUBS0ARD1	—	—	—
SM-J106M	VFJ Fiji	J106MVFJ0AQK1	J106MUBU0AQF1	2018-05-10	1.245 GiB	SM-J106M_1_20180717152458_27yvybqf8m_fac.zip

Device specifications

Display diagonal10.2 cm (4")
Display resolution480 x 800 pixels
Display typeTFT
RAM1 GB
Rear camera resolution5 MP
Rear camera typeSingle camera
Battery capacity1500 mAh
Weight123 g

Specifications of SM-J106, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash J106MUBS0ARD1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

J106MUBS0ARD1 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

J106MUBS0ARD1 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy J1 Mini Prime, released for Fiji (VFJ), Papua New Guinea (PNG). Samsung built it on 2018-04-04.

No. A newer build for SM-J106M is available: J106MUBU0ARL2. Install it instead of J106MUBS0ARD1 unless you need this exact version. The previous build was J106MUBU0ARD1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J1 Mini Prime must be on bootloader binary 0 or lower.

This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy J1 Mini Prime running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 21 other builds of this model use the same binary, so you can switch between them in both directions.