SM-J110H 1 country Android 4.4.4 (KitKat)

Samsung Galaxy J1 Ace J110HXXU0AQF2 Firmware

Name: Samsung Galaxy J1 Ace (SM-J110H)
Brand: Samsung
Availability: InStock

Samsung Galaxy J1 Ace J110HXXU0AQF2 is an Android 4.4.4 (KitKat) firmware for India (INS). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J110HXXS0AQF1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J110H is available: J110HXUU0AQK2.

9.4/10 (35)4,546 times

Android 4.4.4 (KitKat)

OS Version

2017-06-23

First release

other regions until 2017-07-07

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Model	Region	CSC Version	MODEM/CP Version	Build Date	Release date	Size	File name	Download
SM-J110H	INS India	J110HODD0AQF2	J110HDDU0AQF1	2017-07-07	2017-07-11	513.786 MiB	SM-J110H_1_20170707115640_z0vr44oxig_fac.zip
SM-J110H	INS India	J110HODD0AQF2	J110HXXU0AQF2	2017-06-23	—	—	—

Device specifications

Display diagonal10.9 cm (4.3")
Display resolution480 x 800 pixels
Display typeSAMOLED
Processor frequency1.3 GHz
RAM0.512 GB
Rear camera resolution5 MP
Rear camera typeSingle camera
Battery capacity1800 mAh
Weight128 g

How to flash J110HXXU0AQF2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

J110HXXU0AQF2 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

J110HXXU0AQF2 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy J1 Ace, released for India (INS). Samsung built it on 2017-06-23.

No. A newer build for SM-J110H is available: J110HXUU0AQK2. Install it instead of J110HXXU0AQF2 unless you need this exact version. The previous build was J110HXXS0AQF1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 513.786 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J1 Ace must be on bootloader binary 0 or lower.

This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy J1 Ace running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 41 other builds of this model use the same binary, so you can switch between them in both directions.