Samsung Galaxy J2 J200GDCU2ASK1
SM-J200G 3 countries Android 5.1.1

Samsung Galaxy J2 J200GDCU2ASK1 Firmware

Samsung Galaxy J2 J200GDCU2ASK1 is an Android 5.1.1 firmware for Bangladesh (BKD, BNG), Nepal (NPB, NPL), Sri Lanka (SLK). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J200GDCU2ARL1: Android updated from Android 5.1.1 (Lollipop) to Android 5.1.1. This is the newest build for SM-J200G.

9.3/10 (453)22,015 times
Android 5.1.1
OS Version
n/a
Build Date
n/a
Security patch
3
Countries
5
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: J200GDDU2ASK3
    ModelRegionCSC VersionSizeFile nameDownload
    SM-J200G
    BKD Bangladesh
    		J200GODD2ARL1 — —
    SM-J200G
    BNG Bangladesh
    		J200GODD2ARL1 — —
    SM-J200G
    NPB Nepal
    		J200GODD2ARL1 — —
    SM-J200G
    NPL Nepal
    		J200GODD2ARL1 — —
    SM-J200G
    SLK Sri Lanka
    		J200GODD2ARL1 — —

    No matching downloads

    How to flash J200GDCU2ASK1

    • J200GDCU2ASK1 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal11.9 cm (4.7")
    • Display resolution540 x 960 pixels
    • Display typeSAMOLED
    • RAM1 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity2000 mAh
    • Weight130 g

    Specifications of SM-J200, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J200GDCU2ASK1 is Android 5.1.1 firmware for Samsung Galaxy J2, released for Bangladesh (BKD, BNG), Nepal (NPB, NPL), Sri Lanka (SLK).

    Yes. J200GDCU2ASK1 is the newest build for SM-J200G on SamFirm. The previous build was J200GDCU2ARL1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J2 must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy J2 running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 33 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J2

    No changelog details available.
    Model firmware by region