SM-J200M 2 countries Android 5.1.1 (Lollipop)

Samsung Galaxy J2 J200MUBS2AQF2 Firmware

Name: Samsung Galaxy J2 (SM-J200M)
Brand: Samsung
Availability: InStock

Samsung Galaxy J2 J200MUBS2AQF2 is an Android 5.1.1 (Lollipop) firmware for Argentina (PSN, UFN), Uruguay (UFU). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J200MUBU2AQE4, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J200M is available: J200MUBS2ARK7.

9.2/10 (24)13,592 times

Android 5.1.1 (Lollipop)

OS Version

2017-06-07

First release

other regions until 2017-07-13

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

Model	Region	CSC Version	MODEM/CP Version	Build Date	Release date	Size	File name
SM-J200M	PSN Argentina	J200M2AQF2	J200MUBS2AQF2	2017-06-07	—	—	—
SM-J200M	UFN Argentina	J200MTFG2AQC1	J200MUBS2AQF2	2017-06-07	—	—	—
SM-J200M	UFU Uruguay	J200MTFG2AQC1	J200MUBU2AQC1	2017-07-13	2017-07-14	1.031 GiB	SM-J200M_1_20170713143213_62azt5us8q_fac.zip
SM-J200M	UFU Uruguay	J200MTFG2AQC1	J200MUBS2AQF2	2017-06-07	—	—	—

Device specifications

Display diagonal11.9 cm (4.7")
Display resolution540 x 960 pixels
Display typeSAMOLED
RAM1 GB
Rear camera resolution5 MP
Rear camera typeSingle camera
Battery capacity2000 mAh
Weight130 g

Specifications of SM-J200, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash J200MUBS2AQF2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

J200MUBS2AQF2 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

J200MUBS2AQF2 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy J2, released for Argentina (PSN, UFN), Uruguay (UFU). Samsung built it on 2017-06-07.

No. A newer build for SM-J200M is available: J200MUBS2ARK7. Install it instead of J200MUBS2AQF2 unless you need this exact version. The previous build was J200MUBU2AQE4.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.031 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J2 must be on bootloader binary 2 or lower.

This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy J2 running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 26 other builds of this model use the same binary, so you can switch between them in both directions.