SM-J200Y 1 country Android 5.1.1 (Lollipop)

Samsung Galaxy J2 J200YZTS1APJ2 Firmware

Name: Samsung Galaxy J2 (SM-J200Y)
Brand: Samsung
Availability: InStock

Samsung Galaxy J2 J200YZTS1APJ2 is an Android 5.1.1 (Lollipop) firmware for Taiwan (BRI). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J200YZTU1APH1 https://samfirm.shop/build/J200YZTU1APH1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J200Y is available: J200YZTS2ARH1 https://samfirm.shop/build/J200YZTS2ARH1.

9.0/10 (455)4,326 times

Android 5.1.1 (Lollipop)

OS Version

2016-10-18

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J2 use bootloader binary 2 (latest: J200YZTS2ARH1). If your device already runs binary 2, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: J200YZTS1APJ2

Model	Region	CSC Version	Release date	Size	File name	Download
SM-J200Y	BRI Taiwan	J200YZZT1APJ2	2016-11-07	—	—

How to flash J200YZTS1APJ2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

J200YZTS1APJ2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

What's new in J200YZTS1APJ2

- The latest Android security patch has been applied.
ㆍDevice security has been further enhanced.

Device specifications

Launched withAndroid 5.1.1
Display diagonal11.9 cm (4.7")
Display resolution960 x 540 pixels
Display typeSAMOLED
Processor frequency1.3 GHz
Processor familySamsung Exynos
Processor model3475
RAM1 GB
Rear camera resolution5 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity2000 mAh
Weight129 g

Frequently Asked Questions

J200YZTS1APJ2 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy J2, released for Taiwan (BRI). Samsung built it on 2016-10-18.

No. A newer build for SM-J200Y is available: J200YZTS2ARH1. Install it instead of J200YZTS1APJ2 unless you need this exact version. The previous build was J200YZTU1APH1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J2 must be on bootloader binary 1 or lower.

This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy J2 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 10 other builds of this model use the same binary, so you can switch between them in both directions.

Other builds and changelog for Samsung Galaxy J2

J200YZTS2ARH1 +1Jun 5, 2018 - Sep 8, 2018

- The latest Android security patch has been applied.
ㆍDevice security has been further enhanced.

J200YZTS2ARH1Sep 8, 2018
J200YZTU2ARD1Jun 5, 2018

J200YDOU2ARC2 Mar 26, 2018