Samsung Galaxy Grand Prime Pro J250FXWU1AQL5 Firmware
Samsung Galaxy Grand Prime Pro J250FXWU1AQL5 is an Android 7.1.1 (Nougat) firmware for Kazakhstan (SKZ), Russia (SER), Ukraine (SEK). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J250FDXU1AQL3: Android updated from Android 7.1.1 to Android 7.1.1 (Nougat). A newer build for SM-J250F is available: J250FXWU2ATL1.
8.8/10 (452)12,812 times
Android 7.1.1 (Nougat)
OS Version
2017-12-29
Build Date
n/a
Security patch
3
Countries
3
CSC codes
1
Bootloader binary
Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy Grand Prime Pro use bootloader binary 2 (latest: J250FXWU2ATL1). If your device already runs binary 2, this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
MODEM/CP Version: J250FXWU1AQL5
Device specifications
- Display diagonal12.7 cm (5")
- Display resolution540 x 960 pixels
- Display typeSAMOLED
- Processor frequency1.4 GHz
- RAM1.5 GB
- Rear camera resolution8 MP
- Rear camera typeSingle camera
- SIM cardsSingle SIM
- Battery capacity2600 mAh
- Weight153 g
How to flash J250FXWU1AQL5
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- J250FXWU1AQL5 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
J250FXWU1AQL5 is Android 7.1.1 (Nougat) firmware for Samsung Galaxy Grand Prime Pro, released for Kazakhstan (SKZ), Russia (SER), Ukraine (SEK). Samsung built it on 2017-12-29.
No. A newer build for SM-J250F is available: J250FXWU2ATL1. Install it instead of J250FXWU1AQL5 unless you need this exact version. The previous build was J250FDXU1AQL3.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.026 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Grand Prime Pro must be on bootloader binary 1 or lower.
This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Grand Prime Pro running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.