Samsung Galaxy J2 Pro J250MUBS5ASH3 Firmware
Samsung Galaxy J2 Pro J250MUBS5ASH3 is an Android 7.1.1 (Nougat) firmware for Dominican Republic (CDR), Jamaica (JDI). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J250MUBS5ASH2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J250M is available: J250MUBS5ATJG.
8.7/10 (24)8,759 times
Android 7.1.1 (Nougat)
OS Version
2019-08-06
First release
other regions until 2019-08-22
2019-08-01
Security patch
2
Countries
2
CSC codes
5
Bootloader binary
Bootloader binary 5. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
No matching downloads
Device specifications
- Launched withAndroid 7.1.1
- Display diagonal12.7 cm (5")
- Display resolution540 x 960 pixels
- Display typeSAMOLED
- Processor frequency1.4 GHz
- Processor familyQualcomm Snapdragon
- Processor model425
- RAM1.5 GB
- Rear camera resolution8 MP
- Rear camera typeSingle camera
- SIM cardsDual SIM
- Battery capacity2600 mAh
- Weight153 g
What's new in J250MUBS5ASH3
· The security of your device has been improved.
How to flash J250MUBS5ASH3
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- J250MUBS5ASH3 has bootloader binary 5. Your device must run binary 5 or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
J250MUBS5ASH3 is Android 7.1.1 (Nougat) firmware for Samsung Galaxy J2 Pro, released for Dominican Republic (CDR), Jamaica (JDI). It includes the 2019-08-01 security patch. Samsung built it on 2019-08-06.
No. A newer build for SM-J250M is available: J250MUBS5ATJG. Install it instead of J250MUBS5ASH3 unless you need this exact version. The previous build was J250MUBS5ASH2.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J2 Pro must be on bootloader binary 5 or lower.
This build uses bootloader binary 5. It can be flashed on a Samsung Galaxy J2 Pro running binary 5 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 64 other builds of this model use the same binary, so you can switch between them in both directions.