Samsung Galaxy J3(2017) J330NKOU5CTF1
SM-J330N 1 country Android 8.0.0 (Oreo)

Samsung Galaxy J3(2017) J330NKOU5CTF1 Firmware

Samsung Galaxy J3(2017) J330NKOU5CTF1 is an Android 8.0.0 (Oreo) firmware for South Korea (KOO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J330NKOU4CSK2: Android updated from Android 9 (Oreo) to Android 8.0.0 (Oreo); bootloader binary raised from 4 to 5, so after installing it there is no way back to older builds. A newer build for SM-J330N is available: J330NKOU6CUD1.

8.9/10 (454)8,591 times
Android 8.0.0 (Oreo)
OS Version
2020-06-02
First release
other regions until 2020-06-16
n/a
Security patch
1
Countries
1
CSC codes
5
Bootloader binary

Bootloader binary 5. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J3(2017) use bootloader binary 6 (latest: J330NKOU6CUD1). If your device already runs binary 6, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SM-J330N
    KOO South Korea
    		J330NKOO5CTF1J330NKOU5CTE1 2020-06-16 2020-06-16 2.25 GiB
    SM-J330N_1_20200602185720_5rtekytabe_fac.zip
    SM-J330N
    KOO South Korea
    		J330N5CTF1J330NKOU5CTF1 2020-06-02 — — —

    No matching downloads

    How to flash J330NKOU5CTF1

    • J330NKOU5CTF1 has bootloader binary 5. Your device must run binary 5 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution720 x 1280 pixels
    • Display typeTFT-LCD
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity2400 mAh
    • Weight142 g

    Specifications of SM-J330, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J330NKOU5CTF1 is Android 8.0.0 (Oreo) firmware for Samsung Galaxy J3(2017), released for South Korea (KOO). Samsung built it on 2020-06-02.

    No. A newer build for SM-J330N is available: J330NKOU6CUD1. Install it instead of J330NKOU5CTF1 unless you need this exact version. The previous build was J330NKOU4CSK2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.25 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J3(2017) must be on bootloader binary 5 or lower.

    This build uses bootloader binary 5. It can be flashed on a Samsung Galaxy J3(2017) running binary 5 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". No other build of this model uses binary 5.

    Other builds and changelog for Samsung Galaxy J3(2017)

    No changelog details available.
    Model firmware by region