Samsung Galaxy J6 J600NKOU2ARK1
SM-J600N 1 country Android 8.0.0 (Oreo)

Samsung Galaxy J6 J600NKOU2ARK1 Firmware

Samsung Galaxy J6 J600NKOU2ARK1 is an Android 8.0.0 (Oreo) firmware for South Korea (KOO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J600NKOU2ARJ3: Android updated from Android 8.0.0 (Pie) to Android 8.0.0 (Oreo). A newer build for SM-J600N is available: J600NKOS5CUL1.

8.8/10 (473)8,511 times
Android 8.0.0 (Oreo)
OS Version
2018-11-13
First release
other regions until 2018-11-15
n/a
Security patch
1
Countries
1
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J6 use bootloader binary 5 (latest: J600NKOS5CUL1). If your device already runs binary 5, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J600NKOU2ARK1
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-J600N
    KOO South Korea
    		J600NKOO2ARK1 2018-11-15 2018-12-03 2.397 GiB
    SM-J600N_1_20200107113815_x313pkapif_fac.zip
    SM-J600N
    KOO South Korea
    		J600N2ARK1 2018-11-13 — — —

    No matching downloads

    How to flash J600NKOU2ARK1

    • J600NKOU2ARK1 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 8.0
    • Display diagonal14.2 cm (5.6")
    • Display resolution1480 x 720 pixels
    • Display typeSAMOLED
    • RAM3 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity3000 mAh
    • Weight154 g

    Specifications of SM-J600F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J600NKOU2ARK1 is Android 8.0.0 (Oreo) firmware for Samsung Galaxy J6, released for South Korea (KOO). Samsung built it on 2018-11-13.

    No. A newer build for SM-J600N is available: J600NKOS5CUL1. Install it instead of J600NKOU2ARK1 unless you need this exact version. The previous build was J600NKOU2ARJ3.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.397 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J6 must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy J6 running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J6

    No changelog details available.
    Model firmware by region