Samsung Galaxy J6+ J610GUBS6CUDA
SM-J610G 6 countries Android 10

Samsung Galaxy J6+ J610GUBS6CUDA Firmware

Samsung Galaxy J6+ J610GUBS6CUDA is an Android 10 firmware for 6 countries, 9 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J610GUBS6CUD9, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J610G is available: J610GUBU7CWB4.

9.4/10 (490)39,524 times
Android 10
OS Version
2021-05-11
First release
other regions until 2021-05-14
2021-04-01
Security patch
6
Countries
9
CSC codes
6
Bootloader binary

Bootloader binary 6. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J6+ use bootloader binary 7 (latest: J610GUBU7CWB4). If your device already runs binary 7, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    3
    MODEM/CP Version: J610GUBS6CUD8
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-J610G
    BRI Taiwan
    GLB, SMA, XTC Philippines
    TNZ, XNZ New Zealand
    XNF
    		J610GOLO6CUDA 2021-05-14 2021-05-11 2.78 GiB
    SM-J610G_2_20210428045014_zhv2k6rbkb_fac.zip
    SM-J610G
    PNG Papua New Guinea
    		J610GPNG6CUD6 2021-05-14 2021-05-14 2.586 GiB
    SM-J610G_2_20210428050040_g2s0vzv05w_fac.zip
    SM-J610G
    VFJ Fiji
    		J610GVFJ6CUD6 2021-05-14 2021-05-14 2.628 GiB
    SM-J610G_2_20210428045106_kqzs4509lb_fac.zip

    No matching downloads

    How to flash J610GUBS6CUDA

    • J610GUBS6CUDA has bootloader binary 6. Your device must run binary 6 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    What's new in J610GUBS6CUDA

    • The security of your device has been improved.

    Rollout of J610GUBS6CUDA by region

    First release
    May 11, 2021
    Last region
    May 14, 2021
    Duration
    4 days
    Regions
    9
    1. Day 1 · · 4 regions
      PhilippinesGLBSMAXTCTaiwanBRI
    2. Day 4 · · 5 regions
      FijiVFJNew ZealandTNZXNZPapua New GuineaPNGXNF

    Device specifications

    • Launched withAndroid 8.1
    • Display diagonal15.2 cm (6")
    • Display resolution1480 x 720 pixels
    • Display typeTFT
    • RAM3 GB
    • Rear camera resolution13 MP
    • Rear camera typeDual camera
    • Battery capacity3300 mAh
    • Weight178 g

    Specifications of SM-J610, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J610GUBS6CUDA is Android 10 firmware for Samsung Galaxy J6+, released for 6 countries, 9 CSC codes. It includes the 2021-04-01 security patch. Samsung built it on 2021-05-11.

    No. A newer build for SM-J610G is available: J610GUBU7CWB4. Install it instead of J610GUBS6CUDA unless you need this exact version. The previous build was J610GUBS6CUD9.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J6+ must be on bootloader binary 6 or lower.

    This build uses bootloader binary 6. It can be flashed on a Samsung Galaxy J6+ running binary 6 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 8 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J6+

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    • The security of your device has been improved.

    • Overall stability of your device has been improved.
    • The security of your device has been improved.

    • The security of your device has been improved.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    Show 8 older builds

    • Added new feature. - Google RCS(Rich Communication Service)
    • The security of your device has been improved.

    • LGPD (General Personal Data Protection Law) has been applied.
    • The security of your device has been improved.

    • The security of your device has been improved.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    · The security of your device has been improved.

    · Security patch update

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    Model firmware by region