Samsung Galaxy J7 J700HXXS2API1
SM-J700H 1 country Android 5.1.1 (Lollipop)

Samsung Galaxy J7 J700HXXS2API1 Firmware

Samsung Galaxy J7 J700HXXS2API1 is an Android 5.1.1 (Lollipop) firmware for Philippines (XTC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J700HXXS2APG1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J700H is available: J700HXWU3BVH1.

8.8/10 (473)4,357 times
Android 5.1.1 (Lollipop)
OS Version
2016-09-15
Build Date
n/a
Security patch
1
Countries
1
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J7 use bootloader binary 3 (latest: J700HXWU3BVH1). If your device already runs binary 3, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J700HXXU2API3
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-J700H
    XTC Philippines
    		J700HOLB2APD2 2016-10-08 897.962 MiB
    SM-J700H_1_20170810082626_5hjq8bgfdh_fac.zip

    No matching downloads

    How to flash J700HXXS2API1

    • J700HXXS2API1 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    J700HXXS2API1 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy J7, released for Philippines (XTC). Samsung built it on 2016-09-15.

    No. A newer build for SM-J700H is available: J700HXWU3BVH1. Install it instead of J700HXXS2API1 unless you need this exact version. The previous build was J700HXXS2APG1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 897.962 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J7 must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy J7 running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 26 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J7

    · The security of your device has been improved.

    • GPS
    The stability has been improved.

    No changelog details available.
    Model firmware by region