Samsung Galaxy J7 Pop J727VPPVRU4BTH3
SM-J727VPP 1 country Android 8.1.0 (Oreo)

Samsung Galaxy J7 Pop J727VPPVRU4BTH3 Firmware

Samsung Galaxy J7 Pop J727VPPVRU4BTH3 is an Android 8.1.0 (Oreo) firmware for United States (VZW). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J727VPPVRS3BTB1: bootloader binary raised from 3 to 4, so after installing it there is no way back to older builds. A newer build for SM-J727VPP is available: J727VPPVRS5BUD1.

9.1/10 (33)4,489 times
Android 8.1.0 (Oreo)
OS Version
2020-08-13
First release
other regions until 2020-08-17
n/a
Security patch
1
Countries
1
CSC codes
4
Bootloader binary

Bootloader binary 4. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J7 Pop use bootloader binary 5 (latest: J727VPPVRS5BUD1). If your device already runs binary 5, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J727VPPVRU4BTH3
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-J727VPP
    VZW United States
    		J727VPPVZW4BTH3 2020-08-17 2020-09-25 2.4 GiB
    SM-J727VPP_1_20200817132734_ib54ezs22t_fac.zip
    SM-J727VPP
    VZW United States
    		J727VPP4BTH3 2020-08-13 — — —

    No matching downloads

    How to flash J727VPPVRU4BTH3

    • J727VPPVRU4BTH3 has bootloader binary 4. Your device must run binary 4 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal14 cm (5.5")
    • Display resolution1280 x 720 pixels
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • Battery capacity3300 mAh
    • Weight169.8 g

    Specifications of SM-J727U, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J727VPPVRU4BTH3 is Android 8.1.0 (Oreo) firmware for Samsung Galaxy J7 Pop, released for United States (VZW). Samsung built it on 2020-08-13.

    No. A newer build for SM-J727VPP is available: J727VPPVRS5BUD1. Install it instead of J727VPPVRU4BTH3 unless you need this exact version. The previous build was J727VPPVRS3BTB1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.4 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J7 Pop must be on bootloader binary 4 or lower.

    This build uses bootloader binary 4. It can be flashed on a Samsung Galaxy J7 Pop running binary 4 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J7 Pop

    No changelog details available.
    Model firmware by region