Samsung Galaxy Note 8.0 M500WKXUBOH1
SHW-M500W 1 country Android 4.4.2 (KitKat)

Samsung Galaxy Note 8.0 M500WKXUBOH1 Firmware

Samsung Galaxy Note 8.0 M500WKXUBOH1 is an Android 4.4.2 (KitKat) firmware for South Korea (ANY). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build M500WKXUBNJ2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SHW-M500W is available: M500WKXUBQA1.

8.9/10 (453)8,631 times
Android 4.4.2 (KitKat)
OS Version
2015-08-04
Build Date
n/a
Security patch
1
Countries
1
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: M500WKXUBOH1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SHW-M500W
    ANY South Korea
    		M500WBNJ2 — — —
    SHW-M500W
    ANY South Korea
    		M500WANYBNJ2 2015-08-17 1.979 GiB
    SHW-M500W_1_20170118150326_tl3xc9qb4l_fac.zip

    No matching downloads

    How to flash M500WKXUBOH1

    • M500WKXUBOH1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    M500WKXUBOH1 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Note 8.0, released for South Korea (ANY). Samsung built it on 2015-08-04.

    No. A newer build for SHW-M500W is available: M500WKXUBQA1. Install it instead of M500WKXUBOH1 unless you need this exact version. The previous build was M500WKXUBNJ2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.979 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note 8.0 must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Note 8.0 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note 8.0

    No changelog details available.
    No changelog details available.
    No changelog details available.
    No changelog details available.
    Model firmware by region