GT-N7100 1 country Android 4.3 (Jelly)

Samsung Galaxy Note 2 (International) N7100UBUEMK2 Firmware

Name: Samsung Galaxy Note 2 (International) (GT-N7100)
Brand: Samsung
Availability: InStock

Samsung Galaxy Note 2 (International) N7100UBUEMK2 is an Android 4.3 (Jelly) firmware for Trinidad & Tobago (TTT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N7100XXSFQE2: Android updated from Android 4.4.2 (KitKat) to Android 4.3 (Jelly); bootloader binary raised from S (28) to U (30), so after installing it there is no way back to older builds. A newer build for GT-N7100 is available: N7100XXDMG1.

9.3/10 (470)4,420 times

Android 4.3 (Jelly)

OS Version

2013-11-11

Build Date

n/a

Security patch

Countries

CSC codes

U (30)

Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note 2 (International) use bootloader binary X (33) (latest: N7100XXDMG1). If your device already runs binary X (33), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: N7100UBUEMJ4

Model	Region	CSC Version	Release date	Size	File name	Download
GT-N7100	TTT Trinidad & Tobago	N7100UUBEMK2	2013-11-29	1.287 GiB	GT-N7100_1_20150926140427_amzsp3lufd_fac.zip

Device specifications

Launched withAndroid 4.1
Display diagonal14.1 cm (5.55")
Display resolution1280 x 720 pixels
Display typeSAMOLED
Processor frequency1.6 GHz
Rear camera resolution8 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity3100 mAh
Weight181.6 g

How to flash N7100UBUEMK2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

N7100UBUEMK2 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

N7100UBUEMK2 is Android 4.3 (Jelly) firmware for Samsung Galaxy Note 2 (International), released for Trinidad & Tobago (TTT). Samsung built it on 2013-11-11.

No. A newer build for GT-N7100 is available: N7100XXDMG1. Install it instead of N7100UBUEMK2 unless you need this exact version. The previous build was N7100XXSFQE2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.287 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note 2 (International) must be on bootloader binary U (30) or lower.

This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Note 2 (International) running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 44 other builds of this model use the same binary, so you can switch between them in both directions.