Samsung Galaxy Note 2 (International) N7100ZCUEOK1
GT-N7100 1 country Android 4.3 (Jelly)

Samsung Galaxy Note 2 (International) N7100ZCUEOK1 Firmware

Samsung Galaxy Note 2 (International) N7100ZCUEOK1 is an Android 4.3 (Jelly) firmware for China (CHN). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N7100ZCUEOI4, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-N7100 is available: N7100XXDMG1.

9.0/10 (473)8,836 times
Android 4.3 (Jelly)
OS Version
2015-11-23
First release
other regions until 2016-01-06
n/a
Security patch
1
Countries
1
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note 2 (International) use bootloader binary X (33) (latest: N7100XXDMG1). If your device already runs binary X (33), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    GT-N7100
    CHN China
    		N7100CHNEOK1N7100ZCUENB1 2016-01-06 2016-01-06 1.2 GiB
    GT-N7100_1_20160106090601_sc88jaa3dp_fac.zip
    GT-N7100
    CHN China
    		N7100EOK1N7100ZCUEOK1 2015-11-23 — — —

    No matching downloads

    How to flash N7100ZCUEOK1

    • N7100ZCUEOK1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 4.1
    • Display diagonal14.1 cm (5.55")
    • Display resolution1280 x 720 pixels
    • Display typeSAMOLED
    • Processor frequency1.6 GHz
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity3100 mAh
    • Weight181.6 g

    Frequently Asked Questions

    N7100ZCUEOK1 is Android 4.3 (Jelly) firmware for Samsung Galaxy Note 2 (International), released for China (CHN). Samsung built it on 2015-11-23.

    No. A newer build for GT-N7100 is available: N7100XXDMG1. Install it instead of N7100ZCUEOK1 unless you need this exact version. The previous build was N7100ZCUEOI4.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.2 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note 2 (International) must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Note 2 (International) running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 44 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note 2 (International)

    No changelog details available.
    Model firmware by region