GT-N8010 2 countries Android 4.4.2 (KitKat)

Samsung Galaxy Note 10.1 N8010XXSDQA2 Firmware

Name: Samsung Galaxy Note 10.1 (GT-N8010)
Brand: Samsung
Availability: InStock

Samsung Galaxy Note 10.1 N8010XXSDQA2 is an Android 4.4.2 (KitKat) firmware for Slovakia (ORX), United Kingdom (O2U). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N8010XXSDQA1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-N8010 is available: N8010XXUDOF2.

8.8/10 (471)12,763 times

Android 4.4.2 (KitKat)

OS Version

2017-01-05

First release

other regions until 2017-04-25

n/a

Security patch

Countries

CSC codes

S (28)

Bootloader binary

Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note 10.1 use bootloader binary U (30) (latest: N8010XXUDOF2). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: N8010XXSDQA2

Model	Region	CSC Version	Build Date	Release date	Size	File name
GT-N8010	O2U United Kingdom	N8010O2UDOF1	—	—	—	—
GT-N8010	ORX Slovakia	N8010ORXDOF2	2017-04-25	2017-04-25	1.138 GiB	GT-N8010_1_20170424195852_cvds4rs6c6_fac.zip
GT-N8010	ORX Slovakia	N8010DOF2	2017-01-05	—	—	—

How to flash N8010XXSDQA2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

N8010XXSDQA2 has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

N8010XXSDQA2 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Note 10.1, released for Slovakia (ORX), United Kingdom (O2U). Samsung built it on 2017-01-05.

No. A newer build for GT-N8010 is available: N8010XXUDOF2. Install it instead of N8010XXSDQA2 unless you need this exact version. The previous build was N8010XXSDQA1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.138 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note 10.1 must be on bootloader binary S (28) or lower.

This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy Note 10.1 running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 7 other builds of this model use the same binary, so you can switch between them in both directions.