Samsung Galaxy Note3 N9005VJSFQB1 Firmware
Samsung Galaxy Note3 N9005VJSFQB1 is an Android 4.4.2 (KitKat) firmware for Chile (CHO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N9005XXUGPOK2: Android updated from Android 5.0 (Lollipop) to Android 4.4.2 (KitKat); bootloader binary raised from G (16) to S (28), so after installing it there is no way back to older builds. A newer build for SM-N9005 is available: N9005ZSUGPJ2.
9.3/10 (451)8,673 times
Android 4.4.2 (KitKat)
OS Version
2017-02-08
First release
other regions until 2017-03-15
n/a
Security patch
1
Countries
1
CSC codes
S (28)
Bootloader binary
Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy Note3 use bootloader binary U (30) (latest: N9005ZSUGPJ2). If your device already runs binary U (30), this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
Device specifications
- Launched withAndroid 4.3
- Display diagonal14.5 cm (5.7")
- Display resolution1920 x 1080 pixels
- Display typeSAMOLED
- Processor frequency2.3 GHz
- RAM3 GB
- Rear camera resolution13 MP
- Rear camera typeSingle camera
- SIM cardsSingle SIM
- Battery capacity3200 mAh
- Weight168 g
How to flash N9005VJSFQB1
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- N9005VJSFQB1 has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
N9005VJSFQB1 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Note3, released for Chile (CHO). Samsung built it on 2017-02-08.
No. A newer build for SM-N9005 is available: N9005ZSUGPJ2. Install it instead of N9005VJSFQB1 unless you need this exact version. The previous build was N9005XXUGPOK2.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.248 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note3 must be on bootloader binary S (28) or lower.
This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy Note3 running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.