SM-N9005 1 country Android 4.4.2 (KitKat)

Samsung Galaxy Note3 N9005XXUEND4 Firmware

Name: Samsung Galaxy Note3 (SM-N9005)
Brand: Samsung
Availability: InStock

Samsung Galaxy Note3 N9005XXUEND4 is an Android 4.4.2 (KitKat) firmware for France (FTM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N9005XXUEND3, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-N9005 is available: N9005ZSUGPJ2.

8.9/10 (471)4,422 times

Android 4.4.2 (KitKat)

OS Version

2014-04-14

Build Date

n/a

Security patch

Countries

CSC codes

U (30)

Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: N9005XXUENC2

Model	Region	CSC Version	Release date	Size	File name	Download
SM-N9005	FTM France	N9005FTMEND1	2014-05-02	1.346 GiB	SM-N9005_1_20170405190626_dhu3jgvmoc_fac.zip

Device specifications

Launched withAndroid 4.3
Display diagonal14.5 cm (5.7")
Display resolution1920 x 1080 pixels
Display typeSAMOLED
Processor frequency2.3 GHz
RAM3 GB
Rear camera resolution13 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity3200 mAh
Weight168 g

How to flash N9005XXUEND4

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

N9005XXUEND4 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

N9005XXUEND4 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Note3, released for France (FTM). Samsung built it on 2014-04-14.

No. A newer build for SM-N9005 is available: N9005ZSUGPJ2. Install it instead of N9005XXUEND4 unless you need this exact version. The previous build was N9005XXUEND3.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.346 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note3 must be on bootloader binary U (30) or lower.

This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Note3 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 53 other builds of this model use the same binary, so you can switch between them in both directions.