SM-N910G 1 country Android 6.0.1 (Marshmallow)

Samsung Galaxy Note4 N910GDTS1DQC1 Firmware

Name: Samsung Galaxy Note4 (SM-N910G)
Brand: Samsung
Availability: InStock

Samsung Galaxy Note4 N910GDTS1DQC1 is an Android 6.0.1 (Marshmallow) firmware for Australia (OPS, TEL, VAU, XSA). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N910GDTS1DQB2 https://samfirm.shop/build/N910GDTS1DQB2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-N910G is available: N910GDTS1DRH2 https://samfirm.shop/build/N910GDTS1DRH2.

9.0/10 (452)17,229 times

Android 6.0.1 (Marshmallow)

OS Version

2017-03-10

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: N910GDTS1DQC1

Model	Region	CSC Version	Size	File name
SM-N910G	OPS Australia	N910G1DPF4	—	—
SM-N910G	TEL Australia	N910G1DPF4	—	—
SM-N910G	VAU Australia	N910G1DPF4	—	—
SM-N910G	XSA Australia	N910G1DPF4	—	—

Device specifications

Display diagonal14.5 cm (5.7")
Display resolution2560 x 1440 pixels
Display typeSAMOLED
RAM3 GB
Rear camera resolution16 MP
Rear camera typeSingle camera
Battery capacity3220 mAh
Weight175 g

Specifications of SM-N9100, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash N910GDTS1DQC1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

N910GDTS1DQC1 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

N910GDTS1DQC1 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy Note4, released for Australia (OPS, TEL, VAU, XSA). Samsung built it on 2017-03-10.

No. A newer build for SM-N910G is available: N910GDTS1DRH2. Install it instead of N910GDTS1DQC1 unless you need this exact version. The previous build was N910GDTS1DQB2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note4 must be on bootloader binary 1 or lower.

This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Note4 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 67 other builds of this model use the same binary, so you can switch between them in both directions.