SM-N910U 2 countries Android 6.0.1 (Marshmallow)

Samsung Galaxy Note4 N910UXXS2DPI2 Firmware

Name: Samsung Galaxy Note4 (SM-N910U)
Brand: Samsung
Availability: InStock

Samsung Galaxy Note4 N910UXXS2DPI2 is an Android 6.0.1 (Marshmallow) firmware for Hong Kong SAR China (TGY), Taiwan (BRI). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N910UXXS2DPI1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-N910U is available: N910UXXU2DVH1.

9.3/10 (451)8,758 times

Android 6.0.1 (Marshmallow)

OS Version

2016-09-29

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: N910UXXS2DPI2

Model	Region	CSC Version	Size	File name	Download
SM-N910U	BRI Taiwan	N910UZZT2DPI2	—	—
SM-N910U	TGY Hong Kong SAR China	N910UZZH2DPI2	—	—

Device specifications

Display diagonal14.5 cm (5.7")
Display resolution2560 x 1440 pixels
Display typeSAMOLED
RAM3 GB
Rear camera resolution16 MP
Rear camera typeSingle camera
Battery capacity3220 mAh
Weight175 g

Specifications of SM-N9100, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash N910UXXS2DPI2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

N910UXXS2DPI2 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

N910UXXS2DPI2 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy Note4, released for Hong Kong SAR China (TGY), Taiwan (BRI). Samsung built it on 2016-09-29.

No. A newer build for SM-N910U is available: N910UXXU2DVH1. Install it instead of N910UXXS2DPI2 unless you need this exact version. The previous build was N910UXXS2DPI1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note4 must be on bootloader binary 2 or lower.

This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy Note4 running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 81 other builds of this model use the same binary, so you can switch between them in both directions.

Other builds and changelog for Samsung Galaxy Note4

N910UXXU2DVH1 Aug 18, 2022

• GPS
The stability has been improved.
• Security
The device is protected with improved security.

N910UXXU2DVG1 Aug 19, 2022