Samsung Galaxy Note10+ N975FXXS6CTGB Firmware
Samsung Galaxy Note10+ N975FXXS6CTGB is an Android 10 firmware for 4 countries, 5 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N975FXXS6CTGA, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-N975F is available: N975FXXU9HXJE.
OS updates guaranteed until:
Android 12. Security updates until:
Aug 23, 2023
8.8/10 (475)21,554 times
Android 10
OS Version
2020-07-30
Build Date
n/a
Security patch
4
Countries
5
CSC codes
6
Bootloader binary
Bootloader binary 6. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy Note10+ use bootloader binary 9 (latest: N975FXXU9HXJE). If your device already runs binary 9, this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
MODEM/CP Version: N975FXXS6CTGA
No matching downloads
Device specifications
- Launched withAndroid 9.0
- Display diagonal17.3 cm (6.8")
- Display resolution3040 x 1440 pixels
- Display typeDynamic AMOLED
- Processor frequency2.7 GHz
- RAM12 GB
- Rear camera resolution12 MP
- Rear camera typeQuad camera
- SIM cardsHybrid dual SIM
- Battery capacity4300 mAh
- Weight196 g
How to flash N975FXXS6CTGB
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- N975FXXS6CTGB has bootloader binary 6. Your device must run binary 6 or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
N975FXXS6CTGB is Android 10 firmware for Samsung Galaxy Note10+, released for 4 countries, 5 CSC codes. Samsung built it on 2020-07-30.
No. A newer build for SM-N975F is available: N975FXXU9HXJE. Install it instead of N975FXXS6CTGB unless you need this exact version. The previous build was N975FXXS6CTGA.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note10+ must be on bootloader binary 6 or lower.
This build uses bootloader binary 6. It can be flashed on a Samsung Galaxy Note10+ running binary 6 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 20 other builds of this model use the same binary, so you can switch between them in both directions.