Samsung Galaxy Note10+ 5G N976VVRU2BSL7
SM-N976V 1 country Android 10

Samsung Galaxy Note10+ 5G N976VVRU2BSL7 Firmware

Samsung Galaxy Note10+ 5G N976VVRU2BSL7 is an Android 10 firmware for United States (VZW). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N976VVRS2ASJ8: Android updated from Android 9 to Android 10. A newer build for SM-N976V is available: N976VVRU8HXJ1.

OS updates guaranteed until: Android 12Security updates until: Aug 26, 2023
9.1/10 (455)4,476 times
Android 10
OS Version
2019-12-10
Build Date
n/a
Security patch
1
Countries
1
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note10+ 5G use bootloader binary 8 (latest: N976VVRU8HXJ1). If your device already runs binary 8, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: N976VVRU2BSL7
    ModelRegionCSC VersionSizeFile nameDownload
    SM-N976V
    VZW United States
    		N976V2BSL7 — —

    No matching downloads

    How to flash N976VVRU2BSL7

    • N976VVRU2BSL7 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 9.0
    • Display diagonal17.3 cm (6.8")
    • Display resolution3040 x 1440 pixels
    • Display typeDynamic AMOLED
    • RAM12 GB
    • Rear camera resolution16 MP
    • Rear camera typeQuad camera
    • Battery capacity4300 mAh
    • Weight198 g

    Specifications of SM-N976B, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    N976VVRU2BSL7 is Android 10 firmware for Samsung Galaxy Note10+ 5G, released for United States (VZW). Samsung built it on 2019-12-10.

    No. A newer build for SM-N976V is available: N976VVRU8HXJ1. Install it instead of N976VVRU2BSL7 unless you need this exact version. The previous build was N976VVRS2ASJ8.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note10+ 5G must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy Note10+ 5G running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note10+ 5G

    No changelog details available.
    Model firmware by region