SM-N976V 1 country Android 10

Samsung Galaxy Note10+ 5G N976VVRU4CTG3 Firmware

Name: Samsung Galaxy Note10+ 5G (SM-N976V)
Brand: Samsung
Availability: InStock

Samsung Galaxy Note10+ 5G N976VVRU4CTG3 is an Android 10 firmware for United States (VZW). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N976VVRS4CTF3, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-N976V is available: N976VVRU8HXJ1.

OS updates guaranteed until: Android 12Security updates until: Aug 24, 2023

9.2/10 (453)4,245 times

Android 10

OS Version

2020-07-27

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 4. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note10+ 5G use bootloader binary 8 (latest: N976VVRU8HXJ1). If your device already runs binary 8, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: N976VVRU4CTG3

Model	Region	CSC Version	Size	File name	Download
SM-N976V	VZW United States	N976V4CTG3	—	—

Device specifications

Launched withAndroid 9.0
Display diagonal17.3 cm (6.8")
Display resolution3040 x 1440 pixels
Display typeDynamic AMOLED
RAM12 GB
Rear camera resolution16 MP
Rear camera typeQuad camera
Battery capacity4300 mAh
Weight198 g

Specifications of SM-N976B, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash N976VVRU4CTG3

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

N976VVRU4CTG3 has bootloader binary 4. Your device must run binary 4 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

N976VVRU4CTG3 is Android 10 firmware for Samsung Galaxy Note10+ 5G, released for United States (VZW). Samsung built it on 2020-07-27.

No. A newer build for SM-N976V is available: N976VVRU8HXJ1. Install it instead of N976VVRU4CTG3 unless you need this exact version. The previous build was N976VVRS4CTF3.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note10+ 5G must be on bootloader binary 4 or lower.

This build uses bootloader binary 4. It can be flashed on a Samsung Galaxy Note10+ 5G running binary 4 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.