Samsung Galaxy Tab A (2016) with S Pen P585JXU1APL3 Firmware
Samsung Galaxy Tab A (2016) with S Pen P585JXU1APL3 is an Android 6.0.1 (Nougat) firmware for South Africa (XFA, XFV). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P585JXU1APL2: Android updated from Android 6.0.1 (Marshmallow) to Android 6.0.1 (Nougat). A newer build for SM-P585 is available: P585JXS3CTL1.
9.3/10 (451)8,674 times
Android 6.0.1 (Nougat)
OS Version
2016-12-28
Build Date
n/a
Security patch
1
Countries
2
CSC codes
1
Bootloader binary
Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy Tab A (2016) with S Pen use bootloader binary 3 (latest: P585JXS3CTL1). If your device already runs binary 3, this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
MODEM/CP Version: P585JXU1APL3
Device specifications
- Launched withAndroid 6.0
- Display diagonal25.6 cm (10.1")
- Display resolution1920 x 1200 pixels
- Processor frequency1.6 GHz
- Processor familySamsung Exynos
- Processor model7870
- Rear camera resolution8 MP
- Rear camera typeSingle camera
- Front camera resolution2 MP
- Wi-Fi standardWi-Fi 5 (802.11ac)
- Weight558 g
How to flash P585JXU1APL3
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- P585JXU1APL3 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
P585JXU1APL3 is Android 6.0.1 (Nougat) firmware for Samsung Galaxy Tab A (2016) with S Pen, released for South Africa (XFA, XFV). Samsung built it on 2016-12-28.
No. A newer build for SM-P585 is available: P585JXS3CTL1. Install it instead of P585JXU1APL3 unless you need this exact version. The previous build was P585JXU1APL2.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab A (2016) with S Pen must be on bootloader binary 1 or lower.
This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Tab A (2016) with S Pen running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.