SM-P601 5 countries Android 4.4.2 (KitKat)

Samsung Galaxy Note 10.1 P601UBSDSA1 Firmware

Name: Samsung Galaxy Note 10.1 (SM-P601)
Brand: Samsung
Availability: InStock

Samsung Galaxy Note 10.1 P601UBSDSA1 is an Android 4.4.2 (KitKat) firmware for 5 countries, 6 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P601XXSDQG1 https://samfirm.shop/build/P601XXSDQG1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-P601 is available: P601XXUDQA1 https://samfirm.shop/build/P601XXUDQA1.

9.0/10 (451)26,274 times

Android 4.4.2 (KitKat)

OS Version

n/a

Build Date

n/a

Security patch

Countries

CSC codes

S (28)

Bootloader binary

Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note 10.1 use bootloader binary U (30) (latest: P601XXUDQA1). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: P601UBUDOJ2

Model	Region	CSC Version	Size	File name
SM-P601	ARO Argentina	P601UUBDSA1	—	—
SM-P601	BVO Bolivia	P601UUBDSA1	—	—
SM-P601	EON Trinidad & Tobago	P601UUBDSA1	—	—
SM-P601	TPA Panama	P601UUBDSA1	—	—
SM-P601	TTT Trinidad & Tobago	P601UUBDSA1	—	—
SM-P601	UPO Uruguay	P601UUBDSA1	—	—

Device specifications

Display diagonal25.6 cm (10.1")
Display resolution2560 x 1600 pixels
Rear camera resolution8 MP
Rear camera typeSingle camera
Front camera resolution2 MP
Wi-Fi standardWi-Fi 5 (802.11ac)
Weight547 g

Specifications of SM-P6010, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash P601UBSDSA1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

P601UBSDSA1 has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

P601UBSDSA1 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Note 10.1, released for 5 countries, 6 CSC codes.

No. A newer build for SM-P601 is available: P601XXUDQA1. Install it instead of P601UBSDSA1 unless you need this exact version. The previous build was P601XXSDQG1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note 10.1 must be on bootloader binary S (28) or lower.

This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy Note 10.1 running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 7 other builds of this model use the same binary, so you can switch between them in both directions.