Samsung Galaxy Tab 7.7 WiFi P6810XXLPL
GT-P6810 1 country Android 3.2 (Honeycomb)

Samsung Galaxy Tab 7.7 WiFi P6810XXLPL Firmware

Samsung Galaxy Tab 7.7 WiFi P6810XXLPL is an Android 3.2 (Honeycomb) firmware for United Kingdom (XEU). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P6810XXLB4, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-P6810 is available: P6810ZSLP8.

9.4/10 (472)8,846 times
Android 3.2 (Honeycomb)
OS Version
2012-07-17
Build Date
n/a
Security patch
1
Countries
1
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab 7.7 WiFi use bootloader binary Z (35) (latest: P6810ZSLP8). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: P6810XXLPL
    ModelRegionCSC VersionBuild DateSizeFile nameDownload
    GT-P6810
    XEU United Kingdom
    		P6810XXLPL 2012-07-17 — —
    GT-P6810
    XEU United Kingdom
    		P6810OXALPL — — —

    No matching downloads

    How to flash P6810XXLPL

    • P6810XXLPL has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    P6810XXLPL is Android 3.2 (Honeycomb) firmware for Samsung Galaxy Tab 7.7 WiFi, released for United Kingdom (XEU). Samsung built it on 2012-07-17.

    No. A newer build for GT-P6810 is available: P6810ZSLP8. Install it instead of P6810XXLPL unless you need this exact version. The previous build was P6810XXLB4.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab 7.7 WiFi must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Tab 7.7 WiFi running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 4 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab 7.7 WiFi

    No changelog details available.
    No changelog details available.
    No changelog details available.
    No changelog details available.
    No changelog details available.
    Show 1 older build
    No changelog details available.
    Model firmware by region